Read the Beforeitsnews.com story here. Advertise at Before It's News here.

By Russet Street Reno
Contributor profile | More stories

Story Views
Now:
Last hour:
Last 24 hours:
Total:

Finishing the floors

Monday, August 11, 2014 20:25

% of readers think this story is Fact. Add your two cents.

Before we started the floor project, I had a freak out about the stain color. I knew we needed something much darker than what we had, due to the dark casing that I was not going to change.

I love that Varathane has tiny little sample packets at Menards, just 30 cents each…a lot better than buying 5 or 6 small cans. Especially because I ended up picking a color I didn’t think I would want. Here are my five choices on a brand new oak baseboard.

At first I thought we liked the third one the best (Early American) but then when I brought the board inside, the second color from the end was clearly the best.

That color was Dark Walnut, which looked so dark and blah on the baseboard. But I knew that when the oil poly went on top, it would warm the color up quite a bit. I also went to a fancy paint place that carries Old Masters stain, I thought the American Walnut I used for our kitchen shelves would be nice, but it turned out super red! I was pretty pissed I wasted 15 bucks on that. Here is the Dark Walnut going on.

I just loved that it was dark enough that only one coat is needed. You can do multiple coats, but once the first coat is absorbed, the subsequent coats don’t sink in as well. We also wipe the stain off immediately, using a lot of elbow grease, that cuts down on drying time and ensures that you don’t have blotches. When we stain, we use cut up t shirts as rags and we wear pants and socks. We also avoid putting our hands right on the floor. The oils from your skin can create marks (and foot prints!) that show in your stain. This happened to me when we did Ashford’s room two years ago, a foot print right in the middle of the doorway!

It became apparent to us while refinishing these floors that the quality of the oak was pretty low compared to the red oak floors in our previous house. Since this place was built in 1973, I’m not necessarily surprised the wood is not top quality, but it still sucked. It didn’t sand as well, and didn’t accept the stain as well, either. But it still looked pretty good when I busted out the poly. We went with Varathane again, because I am familiar with it and it worked out good in our last house.

Ever since our awesome floor guy clued me in to this tip, I’ve used a regular Shur-Line 9-inch paint pad to put on poly. I only buy one, then I wrap it in plastic wrap and freeze it until I’m ready to do the second and third coats. It works really well! I alternate between using a pole attached to the applicator, and holding it by hand, depending on where I’m at in the room.

We found just how difficult it is to see where you have already coated in this house. With a limited amount of windows, there is a very small area of floor with light shining directly on it. By the FOURTH coat (yep, there is a story behind that) we finally realized we needed some help and Shaun hovered over me with one of my photography studio lights! It worked very well to prevent more issues like this….

I still can’t believe I totally missed those sections, and also…we got a severe wake-up call about how often you have to stir satin poly to maintain the satin finish. The matte particles will settle at the bottom of the can if you don’t stir constantly, and on our third - what we thought was final – coat, most of the upstairs was full gloss! You can see in the above pic the satin below the gloss. I was so disgusted.

In the above photo, the gloss started where the window reflection ends. What the heck. Luckily (not luckily, but you know…) I had straight up FALLEN in the third coat of poly in the dining room, so I knew we would have to do a fourth coat, anyway. It was so embarrassing. I flailed around like a fish out of water and Shaun just laughed and laughed about it. Needless to say, we couldn’t fix it all the way and had to redo.

In between each coat, we waited 24 hours then sanded with 220 grit on a pole sander. It looks scary to scuff it so much, but it’s totally necessary for proper adhesion. We always use a tack cloth on the Swiffer to get up all the dust. After our fourth coat, we saw that we had some issues. Apparently 24 hours drying time was not enough by the time we got three coats on, because the fourth coat had a lot of what they call ‘alligator skin’…caused by the previous coat not being dry enough. This picture also highlights a nice brush hair, Shaun had brushed on the first coat before we switched to the pad. Note to self, don’t use cheap stain and poly brushes!

Drips and some dust.

Ugh, a really bad drip and some weird skips.

Random hair. Hard to say what part of the body that one came from….

Trapped particles created these little crosses in some areas, I’m assuming the previous coat wasn’t dry enough and the new coat couldn’t adhere around these little devils.

Back to my point about the sub-par wood, when we sanded the steps we realized they were just cheap pine treads. Why they would put oak everywhere and then install pine treads, I have no idea…but we just stained it the same and of course the soft wood came out much darker because I didn’t have time to go get (or apply) wood conditioner. Maybe one day we will put in good treads, but for now this is ok.

Overall, Ashford’s room is the worst with the scaling and I’m just thanking my lucky stars that these floors will mostly be covered by rugs! I am much happier with the way the house looks, though. New flooring can make such a huge difference! I love how the floors totally match the window now, I’m not planning to paint any windows in this house.

We waited an entire week to replace the furniture, and will wait about four weeks to put down the rugs. I’ve learned my lesson with the rugs, in our last house I had a grid pattern from the rug pad all over the upstairs even when I waited 3 weeks to replace them! Oil just takes so much longer to cure.

One good thing about waiting so long to put back the furniture is Ashford’s antics. He just loves running around in there!

All in all, we ended up spending $180 on the sander rental, $10 on the paint pad, $10 on tack cloths, $15 on two quarts of stain, $240 on 6, count ‘em, 6 gallons of poly. After spending $450 on this project and a week of Shaun’s vacation, I’m not sure we made the best choice. I would’ve rather paid 3k to have someone else do it, frankly. This go around was super stressful, I think I’m losing my mojo sometimes. Oh well, it’s done and we’re moving on!

Source: http://www.russetstreetreno.com/2014/08/finishing-floors.html

Before It’s News® is a community of individuals who report on what’s going on around them, from all around the world.

Anyone can join.
Anyone can contribute.
Anyone can become informed about their world.

"United We Stand" Click Here To Create Your Personal Citizen Journalist Account Today, Be Sure To Invite Your Friends.

Please Help Support BeforeitsNews by trying our Natural Health Products below!

Order by Phone at 888-809-8385 or online at https://mitocopper.com M - F 9am to 5pm EST

Order by Phone at 866-388-7003 or online at https://www.herbanomic.com M - F 9am to 5pm EST

Order by Phone at 866-388-7003 or online at https://www.herbanomics.com M - F 9am to 5pm EST

Humic & Fulvic Trace Minerals Complex - Nature's most important supplement! Vivid Dreams again!

HNEX HydroNano EXtracellular Water - Improve immune system health and reduce inflammation.

Ultimate Clinical Potency Curcumin - Natural pain relief, reduce inflammation and so much more.

MitoCopper - Bioavailable Copper destroys pathogens and gives you more energy. (See Blood Video)

Oxy Powder - Natural Colon Cleanser! Cleans out toxic buildup with oxygen!

Nascent Iodine - Promotes detoxification, mental focus and thyroid health.

Smart Meter Cover - Reduces Smart Meter radiation by 96%! (See Video).

Comments

Online:
Visits:	1,605,488,880
Stories:	8,156,410