In a recent interview I conducted with EMF Solutions‘ Cory Hillis, electromagnetic frequencies that come from appliances, ceiling fans, cell towers, smart meters, laptops and cell phones, along with other electronic devices were discussed and their impact upon our bodies.  The cell phone companies know their products are producing dangerous EMFs and has provided a solution for those, as well as the other things mentioned.  Now, it appears that some of them are actually starting to realize and test for these dangerous frequencies not only on the body but other systems as well, but what do they plan on doing about them?

How To Protect Yourself From 5G, EMF & RF Radiation

BN Frank has the latest on this developing story.

5G warnings and opposition has limited, slowed, and/or stopped deployment including near some U.S. airports due to dangerous interference issues with aviation equipment (see 1, 2, 3, 4).  Of course, interference issues are not isolated to aviation equipment.  In 2020, utility companies and associations filed lawsuits against the Federal Communications Commission (FCC) for not protecting utility infrastructure from potential electrical interference issues with 5G (see 1, 2).  Telecom provider, SpaceX has complained that Dish’s 5G satellites will cause interference issues affecting Starlink satellite service.  DirecTV and RS Submit have also complained about satellite interference issues.  The Department of Defense (DoD) has also been trying to resolve potential 5G network interference issues with military radar.  In August, a bi-partisan group of senators requested that the FCC reconsider harmful interference risks with associated Ligado’s network before allowing it to be activated.  Fortunately last month, Ligado cancelled trial network plans, maybe because of a new report that also warned about interference.

Of course, there have been other significant 5G issues reported including poor service (see 1, 2, 3, 4, 5, 6, 7, 8, 9), cybersecurity (see 1, 2), health, and environmental risks (see 1, 2, 3, 4).  Nevertheless, proponents continue to encourage us to be patient and trusting because eventually saturating the planet with 5G will all work out fabulously.

From RCR Wireless:

Three RF issues in midband spectrum

By Kelly Hill

When it comes to 5G, no band is perfect. In low bands, 5G coverage is maximized and cell sizes can be quite large, the performance of 5G New Radio is limited because of smaller available channel bandwidths. Meanwhile, high-band, millimeter-wave 5G deployments have a number of known RF challenges: Performance can be excellent because of the capacity and bandwidth available, but coverage is a huge and expensive challenge because of the frequencies’ short range and penetration limitations.

But there are RF issues to deal with even in the “goldilocks” midband range of new spectrum that is coming online. Here are three.

In CBRS, power levels are a sticking point

For mobile operators, the power level limitations of CBRS pose a significant conundrum in reconciling use of the band as part of deployment. This has been reflected in comments in the FCC record, with multiple operators from AT&T and Dish Network to the Competitive Carriers Association urging the FCC to allow higher-power operations in the band. Dish, in a 2021 filing prior to the 3.45 GHz auction, said that the disparate power levels between CBRS and other cellular bands “leave a relatively encumbered CBRS band sandwiched between the 3.45 GHz Band and the 3.7 GHz Band, both of which … have services rules optimized for large-scale, wide-channel 5G service offerings. This is akin to connecting two cities with a new 8-lane high-speed roadway, but constructing a stretch of single lane road in the middle. The current U.S. approach undermines the overall usefulness of the entire 3 GHz band, and places the United States at odds with our major global competitors, especially China.” As of yet, however, the FCC has shown no inclination to change the existing power level limits or create a new class of CBRS devices that could operate at higher power.

In addition to the power level issues, there are also concerns about interference between 3.45 GHz operations and the ESC receivers that detect incumbent activity in the 3.55-3.65 MHz portion of the CBRS band. As noted in a WINN Forum document on co-existence between CBRS and ESC sensors, those operations are immediately adjacent to each other. “Because there is no guard band between the two, the ability of ESC sensors to adequately perform their sensing functions could be impacted by strong signals from systems operating in the 3.45 GHz Service,” the document says, with the “dominant predicted impact is from blocking interference from 3.45 GHz Service” rather than out-of-band impacts from CBRS to 3.45 GHz. That interference from 3.45 GHz “could render an ESC sensor inoperable, causing a false activation of incumbent radar activity” which would default to the SAS moving CBRS users out of the band and disrupting operations unnecessarily. Again, this plays out in part as a receiver issue – as WINNForum notes, its specs for CBRS ESC filters focused on spectrum activity above 3.65 GHz, because at the time the spec was developed, there weren’t even plans for a 3.45 GHz service that the receivers would have to filter. (ESC sensors, it should also be noted, live in so-called “whisper zones” for CBRS in-band transmission and are treated by the SAS as incumbents in the band, so the SAS limits CBRS channel assignments around ESCs—which also impacts the ability to deploy CBRS near ESCs along the coasts.)

TDD vs. FDD operations

Whether an operator ran an FDD or TDD network used to be a fairly significant difference—but now, post-CBRS and post-C-Band auctions (both of which are TDD spectrum), all the national U.S. operators are doing both.

“It’s not really talked too much about from an operator standpoint, but when you start frequency coordination, the impact of timing and using GPS timing is very critical,” says Tim Sill, VP of technology and business developmentSill of Alpha Wireless. He spent 16 years at Sprint, which put years of effort and cost into clearing and then using TDD spectrum. TDD, he says, “has nuances that you have to get your arms around. .. You have to understand those nuances and some of the uniquenesses about it.” Loss of GPS signal for an extended period of time is one potential risk to such systems’ operational capabilities, he explains, because eventually the performance of the site would degrade to the point where most calls drop. As an example, he mentions tropospheric tunneling, when temperature inversions in the atmosphere can trap TDD signals and channel them over long distances such that base stations hundreds of miles away can be affected.

“With the evolution of technology and also regulations, it opened the door for higher frequencies. When we go to higher frequencies, we also [have] the possibility of using TDD in a more optimized way,” Fabiano Chaves, senior spectrum standardization specialist at Nokia. “When you go up in frequency and you have wider blocks, it’s really quite more optimal to have TDD because we also have more flexibility.” The smaller channel sizes and dedicated uplink/downlink spectrum in lower bands mean that there is little opportunity to optimize uplink vs. downlink based on traffic needs, he explains. “You have the flexibility with TDD to make adjustments to the uplink/downlink proportion,” Chaves says. “It really depends on how the demand is. With TDD, you can adjust this with the network tools that you have for that.”

The caveat here is that not only would all of an operator’s neighboring TDD base stations have to be synchronized, but neighboring TDD operators would have to coordinate with one another in order to make sure they’re not stepping on each others’ transmit/receive patterns and causing what is known as cross-link interference. Timing and synchronization is particularly important in TDD systems. In an early 2022 LinkedIn post on tracking down interference in a CBRS system, Adam Wohld, an RF deployment engineer and solutions architect, related an instance of an operator struggling with high noise in CBRS channels that couldn’t be located on a spectrum analyzer, but which required a PCI scanner to find the TDD-LTE interference—which he discovered was coming from multiple sites, 10 and 17 miles away that were transmitting when the CBRS site was receiving. “CBRS spectrum allocation is about more than frequency, it’s also about timing. Being able to survey and inspect neighboring site configurations over the air is critical to maintaining LTE and 5G performance on CBRS,” Wohld wrote.

Intermod interference in 5G

Passive intermod, or PIM, is a well-known issue in LTE, particularly in FDD where systems transmit and receive at the same time. In LTE, PIM could be caused by loose or corroded connectors or nearby metallic or rusted objects that reflected RF energy. It can be spotted on a spectrum analyzer by a characteristic “shark fin”-shaped arc, notes Angus Robinson, senior marketing manager at Anritsu.

• How To Protect Yourself From 5G, EMF & RF Radiation
• Grab This Bucket Of Heirloom Seeds & Get Free Shipping With Promo Code TIM
• Build Your Own Food Forest & Save 5% With Promo Code TIMBROWN
• Make Your Own Fulvic/Humic Acid – Use Promo Code TIM You’ll Save $$$
• Get A Great Deal On A Satellite Phone
• Gain Cell Phone Freedom With Volta Wireless and Get Your First Month For Just $9.99 With Promo Code USA1
• Here’s A Way You Can Stockpile Food For The Future
• Stockpile Your Ammo & Save $15 On Your First Order
• Preparing Also Means Detoxifying – Here’s One Simple Way To Detoxify
• Save Up To 66% Off MyPillow with Promo Code TIMBROWN

There is indeed PIM in 5G systems, Robinson adds, and Anritsu’s customers are typically encountering it when they are deploying midband spectrum at the same site as existing LTE systems in lower bands. “It’s not unique to the United States, but I think it’s more prevalent in the United States because in the United States there are more frequencies being used for LTE. So at one cell site, before you’ve got 5G, you’ve got 700/800 LTE, you’ve got 1800 MHz LTE, you’ve got 2.3, 2.4 GHz LTE. And it’s almost inevitable that the intermod products going from those base stations are going to fall in the 3.5 GHz band,” he says. That wasn’t obvious, going into 5G—he says Anritsu, which has established its equipment and solutions as helping to address PIM in previous generations of cellular systems, was skeptical that PIM would be an issue in 5G for a number of reasons: There was often beam-steering involved, so the RF energy is more directed and less likely to strike a PIM source; the systems are mostly TDD, which is less prone to PIM. “But actually, it’s not the inbound PIM that’s the problem,” he clarifies. “It’s the PIM resulting from PCS and AWS meeting with 600 or 700 or 800 MHz LTE and generating PIM products in the 3.5 GHz band.” The intermod products are second and third-order products, so they are 40 or more megahertz wide, and tend to be low-power and fall in both the uplink and the downlink. But the downlink power can usually overpower the intermod, he says; it’s in the uplink where the presence of the interference really matters, because it impacts the weaker signal coming from a handset rather than the transmission from the base station. Thus, for a device at the cell edge, he notes, even low-power intermod in the uplink can impact performance.

While some might quibble about whether to consider this “intermod” rather than “passive intermod,” the point is that there is cellular interference being generated by a cellular system—only instead of an LTE base station interfering with its own operations, the intermod here is the result of legacy LTE transmitters generating intermod products that are interfering with midband 5G operations. Whatever you call it, Robinson says, “I absolutely promise you, it’s a really big and significant issue that operators have only really started to realize and test for in the last six to 12 months.”

Repeat:

Whatever you call it, Robinson says, “I absolutely promise you, it’s a really big and significant issue that operators have only really started to realize and test for in the last six to 12 months.”

OMG!

Additionally, since 2017 doctors and scientists have asked for 5G moratoriums on Earth and in space (see 1, 2) due to biological and environmental health risks and the majority of scientists oppose deployment.  Since 2018 there have been reports of people and animals experiencing symptoms and illnesses after it was activated (see 1, 2. 3, 4, 5).  In 2019, telecom executives gave U.S. congressional testimony that they had NO scientific evidence that 5G is safe.  Some researchers have also suggested that activation may be contributing to COVID-19 infections as well as hundreds of thousands if not millions of bird deaths.  Of course, there are confirmed health risks associated with exposure to 4G and other sources of wireless Wi-Fi radiation and Electromagnetic Fields (aka “Electrosmog”) too.  Nevertheless, the FCC (see 1, 2, 3, 4, 5, 6, 7, 8) – who lost a lawsuit for NOT updating RF guidelines which includes 5G since 1996 – and other American government and state agencies and committees (see 1, 2, 3, 4, 5, 6, 7) have continued to promote and fund 5G deployment and densification (see 1, 2) as well as that of 4G and public Wi-Fi (which also poses known risks).

Of course, even if 5G never works as promised, that may not matter anyway.  The end goal seems to be 6G which reportedly isn’t without risks either (see 1, 2).

Article posted with permission from Sons of Liberty Media